The installation method of domestic fiberglass fishing boat forward push


Installation process of domestic fiberglass fishing boat.

Determine the installation position - the port side or the starboard side of the fishing boat? There is no definite answer to this, it depends on your habit of controlling the fishing boat and fishing. If you are used to driving on the port side, you need to think about the installation on the starboard side, so that the forward push will not obstruct your front view. When determining the orientation of the device, you should also consider the general fishing location and the fishing method used.

Remove the set screw and remove the base of the device. For most of the forward push, the installation hole will be visible.

Assemble the front thrusters before deciding on the location of the installation holes on the deck. Fix the drive rod and propeller head on the base, put the front push in a stowed position on the bow, and place it parallel to the side of the boat.

Push the front drive rod as close as possible to the centerline of the fishing boat, assuming that the drive rod, propeller against the centerline, control the motor when the scene of simple lateral drift.

Domestic fiberglass fishing boat: first position the front end of the base of the device to ensure that the front push does not touch the edge of the bow when running. In general, the front end of the base needs to be flush with the edge of the boat, or perhaps the front end is slightly outstanding (outstanding length should not exceed 1 inch/2.5 cm).

Push forward to adhere to the stowed position, determine the motor propeller head position, to ensure that it does not stand out above the side of the boat, otherwise, if the fishing boat accidentally bumped with the dock or other vertical objects, the motor propeller head simple damage. Generally use a ruler to measure, determine the orientation, to ensure that the motor propeller head in the vertical area of the hull.

Again acknowledge the front end of the installation base position, in the bow position in accordance with the shape of the installation base hole to play two positioning holes, generally have another person to help press the base, the hole does not occur when the movement. After punching the holes, use the screws to fix. Then punch other holes, in order to facilitate the operation, at this moment can be the drive rod, propeller head removed.

Ideally, you will be able to reach the bottom of the deck and fix the motor with the nut fixing bolt. In reality, this is not always the case. If you cannot reach the bottom of the deck to fix it, we recommend using expansion bolts for installation.

After all the installation, then install the base side plate.

Note: When drilling holes in domestic FRP fishing boats, you must use a drill bit with a slightly larger diameter than needed to avoid cracking the gel layer of the hull.

In Related News


Sailing the Future with GOLDLUCK

Quality life comes from the sea Here is a report from Weihai Radio and TV Ocean Channel about JinYun yacht - JinYun sails the future and starts a new life in the sea!


Leaders of Weihai City Federation of Industry and Commerce went to Golden Fortune Yacht Company Limited for observation and research

On May 9, 2020, Miao Jianchen, Vice Chairman of Weihai City Federation of Industry and Commerce, Han Qiang, President of the Association of Extra-Party Intellectuals of New Social Strata, and a dozen other people came to Weihai Jin Yun Yacht Co.


Construction of "Shandong Traffic School-Weihai Jingyun Yacht Intelligent Industrial Park" started

At 9:58 a.m. on April 28, 2020, the project of Shandong Traffic College and JinYun Yachting Intelligent Industrial Park was grandly held at Weihai JinYun Yachting Co., Ltd. The attendees of today's groundbreaking ceremony were Li Zhengtao, Vice President of Shandong Traffic College and Secretary of the Party Committee of Weihai Campus, Cheng Weiyuan, Deputy Secretary of the Discipline Inspection Committee of Shandong Traffic College, Lin Xianqi, Deputy Director of Laser Research Institute of Shandong Academy of Sciences, and Yu Wenhua, Chairman of Weihai JinYun Yachting Co.


2019 China (Zhoushan Islands) International Boat Show

"Beautiful Islands, at Zhoushan" 2019 China (Zhoushan Islands) International Boat Show will be held on May 17-19, 2019 in Zhoushan Donggang Putuo Exhibition Center.


2019 China (Weihai) International Boat, Caravan & Fishing Tackle Supplies Exhibition Successfully Concluded

2019 China (Weihai) International Boat, RV and Fishing Tackle Supplies Exhibition came to an end in the afternoon of May 13 at Weihai International Convention and Exhibition Center.


In mid-September, China Classification Society Qingdao and Weihai Branch ship inspection standard process promotional film started shooting in our company

In September 2018, China Classification Society Qingdao and Weihai Branch ship inspection standard process propaganda film started shooting in our company, which played a benchmark and exemplary role for the development of the same industry.